Amprobe began life in Long Island, NY in the late 1940's under the name Pyramid Instrument Company. In 1960 the company name was formally changed to Amprobe Instrument Corporation. Amprobe continued to design, engineer, manufacture and distribute product from its Lynbrook, NY location until it was merged to form ATP and relocated to South Florida in late 1999. The Amprobe RC-120S Remcon Relay Switch switches AC power on and off by using a low voltage control circuit.
The Wiser Load Control Relay is a component of the Schneider Electric Wiser energy management system. The Load Control Relay reports energy consumption and allows scheduling of power to the attached load (30A and less, 120Vac or 120/24Vac circuits). The Load Control Relay coordinates its operation with the Wiser in-home wireless network. The Wiser Load Control Relay, when paired with other Wiser home management system components, such as Wiser In Home Displays, Wiser Smart Plugs and Wiser Smart Thermostat, delivers seamless and secure wireless connectivity in one complete home energy management system. The Load Control Relay allows the homeowner to improve home energy efficiency through automated, convenient home energy management and facilitates homeowner scheduling of increased power loads. Allows homeowner to opt in and out of energy service provider's demand response events. Displays energy alerts from your energy service provider when you participate in a smart grid energy program. Reduces peak electricity usage and costs, helping to prevent grid overloads and blackouts while helping to increase power efficiency and network reliability. Four event per day timer-based schedules with a unique schedule for each day. Features demand response and load control, remote on/off, duty cycle, simple metering.Need more information on this product? Click here to ask.
PSI Woodworking Products LR220-3 220V Long Ranger Dust Collector SwitchTurn on/off the dust collector anywhere in the shop220 volt, 2.5 hp, 15 amp relay/receiverFCC approved25 amp internal circuit breaker included in the receiver5 foot power cordNeed more information on this product? Click here to ask.
PSI Woodworking LR110-3 110V Long Ranger Dust Collector SwitchPSI Woodworking Long Ranger dust collector switch with 110-volt, 1-1/2-horspower engine and 20-amp relay receiverTurn on a dust collector from anywhere in the shopUses R.F. signal, which is not affected by outside interference by large television transformers, electrical noise, or three-phase power sourcesIncludes a circuit breaker in the receiver and a 5-foot power cordShips at 1.84-poundsNeed more information on this product? Click here to ask.
The latest INSTEON plug-in module, I/O Linc, lets you monitor and control any low voltage devices such as alarm sensors, electric door strikes and contact closures as part of your INSTEON home automation network. With one dry-contact sensor input you can control many INSTEON devices throughout the house. Plus, use the built-in single-pole double-throw (SPDT) switch, connect any low voltage-powered device for continuous or momentary operation. Create your own remote-control door lock using an electric door strike and power supply or use a security sensor turn INSTEON controlled lights on or off. I/O Linc is also backward-compatible with X10.Monitor and control pool valves, electric door strikes, garage doors and more using your INSTEON or X10 network4 output relay modes allow you to control many different types of devicesControl INSTEON lights and appliances using standard sensorsContains 1 sensor input and 1 output relay (NO/NC)Need more information on this product? Click here to ask.
BRK Brands 9120P-48P Hardwired Smoke Alarm w/ Battery Backup, SingleQuantity 48 - 9120B hardwired smoke alarms with battery backup; bulk pack with individual packagingTamper resistant locking pins, single button silence/test and loud 85dB alarm120-Volt AC power with 9-Volt battery backup (included) to keep alarm functioning during power outageOpen mounting design for easy installation with side load battery compartment for quick replacement and interconnectable up to 18 units (12 smoke, 6 CO/heat/relay)10-Year limited warrantyNeed more information on this product? Click here to ask.
The Leviton ODC0S-I7W Ceiling-Mount Self-Contained Occupancy Sensor is the cost-effective choice for commercial and institutional spaces where traditional ceiling-fixture installation is difficult, inconvenient, or costly. Ideal for storage areas, small bathrooms, copy rooms, mop/sink closets, or small spaces without wall switches, this self-contained sensor will help reduce energy costs and it does not require an external power pack and will help reduce energy costs.Motion sensor and relay in one unit; eliminates need for additional control units for power or switchingPassive Infrared (PIR) technology for optimum detection performanceProvides a 360-degree field of view with 530 square feet of coverageAmbient light override for additional energy savingsFluorescent: 2,700VA at 277V ACNeed more information on this product? Click here to ask.
Leviton OSSMT-MDW Ultrasonic/Infrared, Dual-Relay Multi-Technology Wall Switch Sensor Leviton's OSSMT multi-technology Decora brand style wall switch occupancy sensor is used to provide automatic lighting control for energy savings and convenience in a variety of commercial applications, including: - retrofit- private and executive offices- conference rooms- storage areas- restrooms- classrooms- lounges- training areas. The OSSMT provides for automatic switching of incandescent lamps, low-voltage lighting with electronic and magnetic transformers, and electronic and magnetic fluorescent ballasts. For retrofit applications, the OSSMT-GD model does not require a neutral wire for installation. Multi-Technology Wall Switch sensor, 2400 Sq. Ft. Major Motion Coverage, 400 Sq. Ft. Minor Motion Coverage, 800Wat 120v INC, 2400VAat 120v FL, 2700VAat277V FL, 1/4HPat 120v Motor, Commercial Grade - White California Title 24 Compliant.
The Leviton ODC0S-I1W Ceiling-Mount Self-Contained Occupancy Sensor is the cost-effective choice for commercial and institutional spaces where traditional ceiling-fixture installation is difficult, inconvenient, or costly. Ideal for storage areas, small bathrooms, copy rooms, mop/sink closets, or small spaces without wall switches, this self-contained sensor will help reduce energy costs and it does not require an external power pack and will help reduce energy costs.-Motion sensor and relay in one unit; eliminates need for additional control units for power or switching-Passive Infrared (PIR) technology for optimum detection performance-Provides a 360-degree field of view with 530 square feet of coverage-Ambient light override for additional energy savings-Incandescent: 1,000W at 120V AND Fluorescent: 1,000VA at 120VNeed more information on this product? Click here to ask.Dimensions: 0″ x 0″ x 0″. Weight: 0.55lbs.
Leviton OSFHU-ITW Fixture-Mounted PIR High-Bay Sensor w/ 3 Interchangeable Lenses The OSFHU high-bay occupancy sensor is specifically designed for high mounted areas such as warehouses, manufacturing and other high ceiling applications. The OSFHU installs directly to an industrial fluorescent luminaire or an electrical junction box. It is a self-contained sensor and relay that turns individual light fixtures on or off based on occupancy in the detection zone. It comes with three interchangeable lenses for use in either a 360-degrees high-bay or 360-degrees low-bay general area or an aisle way. The OSFHU provides reliable coverage up to 40 ft. Mounting heights. The OSFHU is also available in a model for cold storage applications with temperatures as low as -40-degrees f.
Scenes allow you to control multiple lights, rooms or even the whole home with a single command. Because OutletLinc can be a member of more than 400 scenes (i.e. "Movie Time," "Party," "Romance," etc.), you'll be able to launch various lighting scenarios with a single button press on an INSTEON Controller. These are elegant features usually found only in systems costing tens of thousands of dollars and requiring extensive rewiring of your home. All member lights and appliances can turn on or off instantly, all controlled with one command from one button. If you want to control multiple scenes from one controller, try the INSTEON KeypadLinc Dimmer.Clean in-wall design blends in anywhere in your homeManual ON/OFF button for added convenienceBuilt-in relay allows you to connect devices of any typeTop outlet is INSTEON controlled, bottom outlet is always onNote: If you are using LED lights that are very low wattage, you may notice that the LED's do not turn out completely when plugged into this device. In this case, you'll need to add to the load with more LED's or higher wattage bulbs - generally higher than a 5-watt load.Need more information on this product? Click here to ask.
StarTech RK812WALLO 8U Open Frame Wall Mount Equipment Rack This 8U Open Frame Wall Mount Equipment Rack is a high quality, low cost relay rack that is easy to assemble and install into any environment. The rack can be wall mounted or installed as a free standing storage solution. the wall mounts are positioned 16in apart (center to center), making it suitable for mounting on virtually any wall surface, based on North American wall frame stud spacing standards.Product Dimensions: 21.3" x 26.5" x 4.2" ; 17.6 poundsProduct Features: Unit is shipped with all the hardware necessary to assemble and install components into the rackAble to accommodate common data, audio-video and telecom equipment, the open rack offers a depth of 12in Hardware to mount the rack to the wall is not provided. Flat packaging for easy transportation, with easy assembly Low cost rugged design for simple implementation Package includes necessary hardware for mounting the components Wall mounts are 16 inches from center to center for mounting to any standard studs
The Greengate OSW-P-0451-DMV-V 120-277 Dual-Level PIR Wall Switch Sensor is a self contained, energy saving, motion-sensing lighting control which replaces a conventional wall switch and utilizes ultrasonic technology to detect room motion. The sensor produces a low-intensity, inaudible sound to detect occupancy in a room. Changes in the sensor's acoustic wave caused by motion, such as walking into a room, reaching for a telephone or swiveling in a chair, will cause the lights to turn on. The sensor does not respond to audible sound. The OSW-P-0451-DMV-Vallows the control of two separate loads with one switch. The two circuit/dual-level switch operates the same in the auto and manual modes as the single circuit switch. To change light levels once the lights are on, the user presses and holds the touchplate allowing the lights to cycle through in the following order: primary load only, both loads, secondary loads only. The OSW-P-0451-DMV-V also has an energy saver mode that ensures that the wall switch only activates one load. If both loads are on when the sensor times out, only the primary load will be activated. If only the primary or secondary load was on at time of shut out, the sensor will reactivate the load that was on at the time. If the lights were shut off manually, the switch will activate the primary load only. The OSW-P-0451-DMV-V time-delay is adjustable from 15 seconds to 30 minutes. Greengate wall switches are ideal for smaller spaces where you will not have obstructions of line-of-sight due to switch location, room orientation or furniture placement. An air-gap switch ensures no leakage current to load for maximum product reliability, and zero-crossing technology maximizes relay life and ensures wall switch longevity. The NEMA WD7 Guide robotic method is utilized to verify coverage patterns, there is no minimum load requirement, and the OSW-P-0451-DMV-V has 120 and 277 volts in the same unit.Need more information on this product? Click here to ask.
Simply Automated Custom Expansion Series Powerful custom expansion capability - up to 250 devices using UPStart software, your PC and Computer Interface Module (PN: UMC-USB) USB Computer Interface Module. Plug-in module with 6 foot USB cable to connect a PC to the powerline, enabling communication with and configuration of Simply Automated Universal Powerline Bus (UPB) devices. Used with UPStart software, the interface module provides PC-based configuration and control of lighting scenes, dimmers, modules and other Simply Automated UPB devices over the power line. Can also transmit and receive lighting scene commands with other Simply Automated UPB dimmers, plug-in modules, fixture modules or other devices - can control virtually any device that connects to AC power wiring anywhere in the home. Simply Automated is an industry leader in home automation and lighting control. We provide an optimum solution for your home lighting automation needs -- most complete product line in the industry, powerful UPB powerline technology and low price. Simply Automated products utilize Universal Powerline Bus (UPB) technology. Our products work over the pre-existing electrical wiring in your home. No new wires needed! Powerful expansion capability -- up to 250 devices using UPStart software and your PC and Computer Interface Module (PN: UMC-USB). Add additional single rocker dimmers, deluxe dimmers with different faceplates (up to 8 buttons), lamp or appliance modules, tabletop pedestal with 8 buttons, wall receptacle, fixture relay, fixture dimmer or scheduler-timer. Lighting control for your entire home. To ensure a proper installation in your home: - Your home should be no more than 2500 square feet and have only one breaker panel. A phase coupler is required in some home installations. - Not intended for use in multi-dwelling (condo, apartment, duplex) units.Need more information on this product? Click here to ask.
The HBA OMNIR Digital Passive Infrared Ceiling Occupancy Sensor is covered by a five year limited manufacturer warranty, and is sold one item per package. The OMNI Passive Infrared ceiling mount occupancy sensor represents the state-of-the-art in sensor technology by utilizing passive infrared (PIR) technology for unequaled occupancy detection and false trip immunity. The sensor features HBA's patented IntellADAPT technology that continuously analyzes its environment and self-adapts, eliminating the need for manual sensitivity and timer adjustments during installation as well as over the life of the product. IntellADAPT provides true maintenance free "Install and forget" operation. With optional relay control for use with building automation systems and a photo sensor for automatic daylight harvesting, the OMNI Passive Infrared sensor is simply the most capable ceiling mount occupancy sensor available in the marketplace today. The auto mode is self-adjustable based on occupancy from 8 to 30 minutes. For indoor use only, the switch operates in temperatures of 32 to 104-Degree Fahrenheit (0 to minus 40-Degree Celsius), and relative humidity of less than 95-percent, non-condensing. The cover has an off white finish with dimensions of 4.5 by 1.5-Inch, and includes a mounting base. The sensor's cover range is up to 450-Square Feet. It's versatile for any office, board room, conference room, or small enough for a utility room. Hubbell Building Automation is a strong proponent of innovative, integrated and simple energy saving lighting controls.Need more information on this product? Click here to ask.
Breaker-Mount Phase Coupler. Fits two breaker positions in a standard breaker-panel (Murray/Crouse Hinds - MP, Siemens - QP, Cutler Hammer/Eaton - BR or CL, GE - THQL or THQP, and SquareD - HOM). Boosts powerline signals by providing a bridge between the two, 120 VAC electrical phases (A and B) in a split-phase, 240 VAC home. Without a phase coupler, signals travel out to the street transformer on one phase and comeback in the home on the other phase; usually at a lower (attenuated) level. In homes up to 2000 Sq. Ft. and within 100 feet of the transformer, phase coupling may not be needed. As the size of the home and distance from the transformer increases, phase coupling becomes more important. A phase coupler is recommended in every main breaker panel and sub-panel to ensure maximum signal strength. The wire-in phase coupler is good for UPB, X10 and other higher frequency powerline signals. Simply Automated is an industry leader in home automation and lighting control. We provide an optimum solution for your home lighting automation needs -- most complete product line in the industry, powerful UPB powerline technology and low price. Simply Automated products utilize Universal Powerline Bus (UPB) technology. Our products work over the pre-existing electrical wiring in your home. No new wires needed! Powerful expansion capability -- up to 250 devices using UPStart software and your PC and Computer Interface Module (PN: UMC-USB). Add additional single rocker dimmers, deluxe dimmers with different faceplates (up to 8 buttons), lamp or appliance modules, tabletop pedestal with 8 buttons, wall receptacle, fixture relay, fixture dimmer or scheduler-timer. Lighting control for your entire home. To ensure a proper installation in your home: Your home should be no more than 2500 square feet and have only one breaker panel. A phase coupler is required in some home installations. Not intended for use in multi-dwelling (condo, apartment, duplex) units.Need more information on this product? Click here to ask.
Smarthome OutletLinc INSTEON Remote Control Outlet,Ivory The OutletLinc is a remote controllable wall receptacle that features a top outlet that can be controlled and a bottom pass-through outlet that is always on. You can control the outlet from any INSTEON-compatible controller including a handheld remote, computer, the Internet and more. Turn on a towel warmer, morning coffee and the radio so you can catch the morning traffic - all at the press of a button. With INSTEON, the possibilities are endless! The OutletLinc installs like a traditional receptacle and once installed setup is quick and easy using a simple Plug-n-Tap programming. With high-end quality, countdown features and remote controllability, you'll see how easy it is to create your own smart home. INSTEON is a low-cost home control technology that uses both the existing electrical wires in the home and radio-frequency to communicate. From lighting, appliance and thermostat control to integrated security systems, INSTEON allows you to manage your home the way you want - from a handheld remote, wall keypad, computer or web-enabled device like a smart phone. Easy to install and set up, INSTEON offers the flexibility and dependability to make life more convenient, safe and energy efficient. Note: The OutletLinc uses power line for its communication. When controlling this device from an RF-only device such as a RemoteLinc or motion sensor, be sure to have at least one Access Point or dual-band device installed. These convert RF signals to power line and vice versa. Features: Clean in-wall design blends in anywhere in your homeManual On/Off button for added convenienceBuilt-in relay allows you to connect devices of any typeTop outlet is INSTEON controlled, bottom outlet is always onNeutral wire required; 480 watt maximum load
Check out the most popular brands: Bounty, Seventh Generation & Safety 1st. Get fantastic everyday values across our range of products and a Savings Center that makes it easy to find the stuff on sale this week. We ship via UPS and several other premium carriers to provide expedited service. We don't hide our telephone number, like most websites.